Results 1 to 5 of 5

Thread: Synchros ?

  1. #1
    Inactive Member 97SCGS's Avatar
    Join Date
    April 17th, 2001
    Posts
    72
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Question

    Hey Guys, I changed my e-mail address& I had to register all over again, anyway....? for ya. Does anyone know about synchros, like where to get them or how much..and If I have to by them in a set..is that the best way to buy them? I called Acura, some of those guys..brain dead...THey quoted me a big price..Any help would be appreciated Thanks guys...It's good to be back!!

    ------------------
    97 Teg GS
    @8-PSI Aem CAI,DC Header,DC catback Exhaust,BBk 62mm TB,B&M FPR,B&M S.Shifter,ECU,8 psi upgrade,Walbro FP,Cartech FMU,RC 310's,JR-BTC,& a bunch of cosmetics.

  2. #2
    Inactive Member TurboGSR's Avatar
    Join Date
    February 15th, 1999
    Posts
    242
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    e-mail mike k...
    [email protected]

    he works in the parts department down in naples acura, FL

  3. #3
    Inactive Member 00civic's Avatar
    Join Date
    December 5th, 2000
    Posts
    129
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I replaced my syncros in my ls tranny, and the only way I could get the syncros is to just buy a use main and counter shaft that was in good condition..(cheapest way)
    you could try Mike but I dont know if he can get the actual syncros w/o having to buy the entire gear-set.

    [This message has been edited by 00civic (edited April 17, 2001).]

  4. #4
    Inactive Member 97SCGS's Avatar
    Join Date
    April 17th, 2001
    Posts
    72
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Thanks Guys....any other suggestions would be great too.....

    I'll try Mike K..

    Hey 00Civic...How much did you pay for the used main and counter shaft?....even though your down south and the price will fluctuate it can't be that off.

    Thanks again guys any more help would be appreciated.

  5. #5
    Inactive Member 00civic's Avatar
    Join Date
    December 5th, 2000
    Posts
    129
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I got it from out west, from Mr Dan Phan(aka dog-eatin-dan(hybrid page)) I think it was 100-150 for the mainshaft?, its been a while but I wouldn't pay more than that..I only needed the syncros and shift rings off of the mainshaft, as it was the common 3rd gear grind.. hit him up see if he has some in stock..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •